52 Tons HMGOLD™7000 to Peru: CIP Recovery from 93.5% to 97.3%

A gold mine in La Libertad, Peru — processing 3,000 tons of ore per day through a CIP circuit — was losing 8–10% of its carbon inventory every elution cycle. The old carbon had a ball-pan hardness of just 94%. Recovery had dropped from 96% to 93.5%, and the operation was bleeding gold into tailings. After switching to HMGOLD™7000 (iodine ≥1,100 mg/g, hardness ≥99%, 6×12 mesh), carbon loss dropped to 2.5–3% per cycle, recovery climbed to 97.3%, and the mine recovered an extra ~320 grams of gold per day — approximately $24,000 in additional daily revenue at the time of reporting. This is how that project came together.

The Problem: 94% Hardness Carbon Was Destroying Recovery

The mine's CIP circuit ran six adsorption tanks in series. The carbon they were using — a generic coconut shell product from a Southeast Asian supplier — was specified at 94% ball-pan hardness. On paper, 94% sounds fine. In a 3,000 tpd CIP circuit, it's not.

Here's what was happening:

Metric	Before (Old Carbon)	Target
Ball-pan hardness	94%	≥98%
Carbon loss per elution	8–10%	<3%
Gold recovery rate	93.5% (declining)	≥96%
Fine carbon in tailings	Visible on screens	Minimal
Elution cycles before replacement	30–40 cycles	50+ cycles

The mechanism is straightforward: every time carbon goes through the elution kiln and gets pumped back into the adsorption circuit, the granules collide with each other, the ore slurry, and the inter-stage screens. Low-hardness carbon breaks down into fines. Those fines are too small to be retained by the screens — they pass through and end up in tailings, carrying adsorbed gold with them.

At 8–10% loss per cycle, the mine was replacing its entire carbon inventory roughly every 10–12 cycles. That's not just a carbon cost problem — it's a gold loss problem. Every kilogram of carbon fines leaving the circuit carries gold that will never be recovered.

Why Hardness Matters More Than Iodine Number in High-Throughput CIP

Most buyers ask about iodine number first. It makes sense — iodine number indicates adsorption capacity, and higher numbers mean faster gold loading. But in a high-tonnage CIP circuit like this one, hardness is the controlling parameter.

Here's the math that convinced this buyer:

Scenario	94% Hardness	99% Hardness
Starting carbon inventory	52 tons	52 tons
Loss per elution cycle	9% (midpoint)	2.75% (midpoint)
Carbon lost per cycle	4.68 tons	1.43 tons
Cycles to lose 50% inventory	~7 cycles	~24 cycles

*Based on 26 elution cycles/year (biweekly), FOB carbon price ~$1,800/ton for gold-grade coconut shell GAC.

The carbon replacement cost difference alone is ~$145,000/year. Add the gold recovery improvement (from 93.5% to 97.3% on 3,000 tpd of ore), and the economics become overwhelming.

Huamei's Recommendation: HMGOLD™7000

After reviewing the mine's circuit design, ore characteristics, and operating conditions, we recommended HMGOLD™7000 — not the higher-grade HMGOLD™7500 or PLUS. Here's why:

Parameter	HMGOLD™7000	Old Carbon	Why It Matters
رقم اليود	≥1,100 mg/g	~1,000 mg/g	Faster gold loading in the first 2–3 tanks
Ball-Pan Hardness	≥99%	94%	Dramatically reduces carbon fines and gold loss
Ash Content	≤3%	~5%	Less inert material, more active carbon surface
رُطُوبَة	≤5%	~6%	Less water weight per bag
Mesh Size	6×12	6×12	Standard CIP sizing — no screen modifications needed

Why not HMGOLD™7500 or PLUS? The mine's ore grade and circuit throughput didn't justify the premium. HMGOLD™7000's ≥1,100 mg/g iodine number was more than sufficient for this operation, and the ≥99% hardness — actually higher than both HMGOLD™7500 (≥98.5%) and PLUS (≥98%) — was the priority for solving their carbon loss problem. We recommended the grade that solved the specific problem, not the most expensive option.

Shipment: 52 Tons in 4 × 20ft Containers to Callao

Item	Details
منتج	HMGOLD™7000 Coconut Shell Activated Carbon
Quantity	52 tons (4 × 13 tons per 20ft container)
التعبئة والتغليف	25 kg woven bags on pallets
Destination Port	Callao, Peru
Origin Port	Xiamen, China
Transit Time	~15 days (sea freight)
Documentation	COA per container, MSDS, phytosanitary certificate

Each 20ft container was loaded with 13 tons — the standard loading capacity for 25 kg bags on pallets in a 20ft dry container. The mine requested COA testing for each container lot, including iodine number, hardness, ash, moisture, and particle size distribution. All four lots tested above spec.

Results After 6 Months

The mine ran HMGOLD™7000 through their full CIP circuit for six months before reporting back. The numbers:

Metric	Before (Old Carbon)	After 6 Months (HMGOLD™7000)	Change
Gold recovery rate	93.5%	97.3%	+3.8 percentage points
Carbon loss per elution	8–10%	2.5–3%	Reduced by ~70%
Additional gold recovered/day	Baseline	+~320 grams	~$24,000/day additional revenue
Carbon inventory stability	Full replacement every 10–12 cycles	Stable with top-up only	Replacement cost down ~70%
Fine carbon in tailings	Visible on inter- stage screens	Minimal	Significant reduction

The 3.8-point recovery improvement came from two sources: (1) less gold leaving the circuit on carbon fines, and (2) higher iodine number providing better adsorption kinetics in the lead tanks. The mine estimated the combined impact at roughly 320 grams of additional gold recovered per day across their 3,000 tpd throughput — approximately $24,000 per day in additional revenue based on the gold price at the time of reporting. That's from a carbon change that cost under $100,000.

Reorder: 56 Tons in 2 × 40ft Containers

Based on the six-month results, the mine placed a reorder for 56 tons — this time in two 40ft high-cube containers (28 tons each) instead of four 20ft containers. The switch to 40ft containers reduced per-ton shipping cost by approximately 15%.

The reorder also included a request to pre-screen the carbon to tighten the 6×12 mesh distribution — minimizing the fraction of particles near the upper and lower size limits. This is a detail that experienced gold mine operators pay attention to: tighter particle size distribution means more uniform flow through the carbon bed and more consistent gold loading across all tanks.

What This Case Tells You About Choosing CIP Carbon

If you're running a CIP or CIL gold circuit and evaluating carbon suppliers, this project highlights three things:

1. Hardness is not optional. In circuits processing more than 1,000 tpd, anything below 97% ball-pan hardness will cost you in carbon loss and gold recovery. The 5-point difference between 94% and 99% hardness translated to a 70% reduction in carbon loss per cycle.
2. The cheapest carbon is rarely the cheapest option. The old carbon was priced lower per ton, but the mine was replacing inventory 3× faster and losing gold to tailings. Total cost of ownership — including carbon replacement and gold loss — favored the higher-spec product by a wide margin.
3. Match the grade to the circuit, not the brochure. We recommended HMGOLD™7000, not the top-tier PLUS, because this mine's specific problem was hardness, not adsorption capacity. Over-specifying wastes money; under-specifying loses gold.

أسئلة مكررة

What causes high carbon loss in CIP gold circuits?

The primary cause is low ball-pan hardness — carbon with hardness below 97% breaks down rapidly during elution, screening, and inter-stage pumping in CIP circuits. Secondary causes include oversized or undersized particles (poor mesh distribution), excessive pumping velocity, and thermal shock during kiln regeneration. In this Peru case, upgrading from 94% to 99% hardness reduced carbon loss from 8–10% to 2.5–3% per elution cycle.

How much activated carbon does a CIP gold mine need?

A typical CIP circuit carries 10–20 kg of carbon per ton of ore processed per day. For a 3,000 tpd operation, that's 30–60 tons of carbon in the circuit at any time. Initial loading for this Peru mine was 52 tons. The exact quantity depends on the number of adsorption stages, tank volume, carbon concentration, and residence time.

What is the difference between HMGOLD™7000 and HMGOLD™7500?

HMGOLD™7000 has an iodine number ≥1,100 mg/g with ≥99% ball-pan hardness. HMGOLD™7500 has a higher iodine number (≥1,150 mg/g) but slightly lower hardness specification (≥98.5%). For circuits where carbon durability is the priority (high-throughput CIP), HMGOLD™7000 is often the better choice. For CIL circuits where faster adsorption kinetics matter more, HMGOLD™7500 may be preferred. See the full HMGOLD™ product comparison.

Can I test HMGOLD™ carbon before ordering a full container?

Yes. We provide sample quantities (25–50 kg) for lab-scale gold adsorption testing (R-value and K-value tests). Many buyers run a 1–2 ton trial lot in a single adsorption tank before committing to a full circuit change. Minimum production order is 10 tons (one 20ft container).

How long does it take to ship activated carbon from China to Peru?

Sea freight from Xiamen or Ningde port to Callao typically takes 30–40 days. Production lead time is 15–25 days for standard grades, so total door-to-door is approximately 45–65 days from order confirmation. We can also arrange CIF Callao pricing if needed.

Evaluating carbon options for your CIP or CIL circuit? Send us your current carbon specs and circuit conditions — we'll recommend the right HMGOLD™ grade and provide a quote:

• WhatsApp: +86 181-3792-7803
• البريد الإلكتروني: sale@huameicarbon.com